Ashly PE-1200 Power Amplifiers
Ashly Audio : PE-1200
Stereo Power Amplifier, 800 Watts per Channel at 4 Ohms
Large Front View (90 k)
Large Rear View (96 k)
Related PDF Documents
Users Manual (965 k)
Click Get Acrobat image to download Adobe Acrobat reader.
eMail A Friend About This Product
eMail this page to a friend
PE Series (Protea Enabled) amplifiers are high-power, high-efficiency, lightweight amplifiers incorporating the latest in power and control technologies. Each amplifier can be controlled and monitored through the built-in Ethernet port using Proteane Software™. Proteane gives users access to many features, including: input attenuation, channel mute, channel polarity, input level, output voltage, output current, clipping, temperature, and power on/off.
By adding Ashly’s Protea DSP technology and control to an amplifier, we have designed a comprehensive and easy to use audio system. With the introduction of the PE Series amplifiers, we’ve taken Protea technology to the next level. Proteane Software allows you to setup, control and monitor PE Series amplifiers using standard, inexpensive, readily-available Ethernet hardware. Nothing proprietary here! Control anywhere from one to hundreds of amps, as well as your Protea Series processors, on- or off-site with our intuitive and friendly Proteane Software.
There are six models of PE Series amplifiers, all of which share the same PE feature set, that cover a wide range of power requirements from 400W to 1900W per channel @4 ohms. Each utilizes a 2-stage high-efficiency switched mode power supply, which provides a high-power-to-weight ratio. All are two rack units high and weigh only 20lbs! All models will drive 2, 4 or 8 ohm loads.
Input connections are via XLR-1/4” Neutrik combo connectors and 6-pin Euroblock. XLR male connectors are also provided for looping to additional amplifiers. Output connectors are locking Neutrik Speakon and 4 position screw terminal strip with safety cover.
Each PE Series amplifier provides on-board analog processing, including a selectable subsonic filter, a selectable clip-limiter and an input-sensitivity selector, which can optimize the amplifier for load and the many devices that can drive it. Plus, we’ve included an array of output current and temp indicators to monitor various operating parameters. It’s easy to tell at a glance, for example, the status of the load being driven (i.e. “are my drivers working?”). The PE Series also provides DC voltage control of the calibrated Input attenuators, which makes it a snap to control volume from remote locations, and Remote Power Turn-on/-off with sequential power in/off circuitry built right into the amplifier.
Need more? Proteane DSP Cards can be installed as needed. Their SHARC 32-bit/96kHz processor enables 24-bit AD/DA, analog and digital (AES/EBU) inputs. Each offers two additional processed output channels to drive additional amplifier channels. Our current DSP library includes EQ, HPF/LPF, Delay, Compressor/Limiter, Gain, and Routing.
Ashly has long believed that the secret to great sound and reliability is intelligent design and meticulous execution. Our PE Series takes that philosophy and multiplies it ten-fold. Optimized for cool operation, modularity, ultimate compatibility and maximum performance, the PE Series is the amplifier line you’ve been waiting for.
When your next project requires high performance amplifiers with superb sound, reliability, remote control and more, Ashly Audio’s PE Series of remote-controlled power amplifiers have been designed to meet the needs of both portable and installation applications.
Signal to Noise (20 Hz-20 kHz, unweighted):
3800: >112 dB
800: Bipolar, Class AB
1200: Bipolar, Class AB
1800: Bipolar, Class H
2400: Bipolar, Class H
3000: Bipolar, Class H
3800: Bipolar, Class H
Power Requirements (1/8 Power Pink Noise @ 4 Ohm):
Current Requirements-Both Channels Driven
typ = 1/8 output, pink noise
Model idle 8 ohms 4 ohms Power Connector
typ max typ max
800 2.4A 6.6A 13.6A 9.4A 21.8A 15A Edison
1200 2.8A 8.6A 20.2A 13.6A 33.8A 30A Twistlock
1800 2.4A 8.4A 26.2A 13A 42A 30A Twistlock
2400 2.4A 10.4A 33A 15.8A 54A 30A Twistlock
3000 2.6A 12.4A 42A 19.6A 68A 30A Twistlock
3800 2.8A 14.6A 50A 22.6A 80A 30A Twistlock
Voltage Gain: 26dB, 32dB or 1.5V sensitivity (selectable)
Distortion (SMPTE, typical) - 8 ohm load, 10dB below rated power:<0.01%
Distortion (THD+N, typical) - 8 ohm load, 10dB below rated power, 20Hz - 10kHz: <0.01%
Frequency Response: 20Hz - 20kHz, +/- 0.15 dB
Damping Factor - 8 ohm load, <1kHz: > 400
Input Impedance: 20k Ohm, balanced
Maximum Input Level: +21 dBu Cooling: Temperature dependent speed-controlled axial fan, front to back air flow
Control Network: onboard, compatible with standard 100 MB Ethernet hardware
Front Panel Indicators:
Per channel: Clip, -6 dB, -12 dB, -18 dB, Temp, Output current.
Overall: power, standby, protect, bridged mono, parallel mono, communications
Attenuators: 1 per channel: front panel, software, offset and remote
Input Connectors, each channel: XLR female/TRS, Euroblock, XLR male (looping)
Output connectors, each channel: Speakon, screw terminals
Amplifier Protection: inrush current limitation, temperature monitoring heat-sinks, output DC protection, power transistor SOA protection, output over-current protection, mains fuses protection
Load Protection: Adjustable clip limiter
Dimensions: 19"W x 3.5"H x 15.5"D (483mmW x 88.9mmH x 394mmD)
Net; 22 to 24lbs., 10 to 10.9kg
Shipping; 27 to 29 lbs., 12.3 to 13.2 kg
|We provide great low prices for professional audio video and lighting for churches and stage From bose speakers to Yamaha digital mixers|
• Sale Items • Amp Comparison • Mixer Shoot Out •